Trend NX Variable Speed Drives Manual de usuario Pagina 100
- Pagina / 136
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
CONTROL KEYPAD vacon • 83
24-hour support +358 (0)40 837 1150 • Email: [email protected]
7
7.3.4.3 Fault time data record
When a fault occurs the information described above in 7.3.4 is displayed. By pushing the
Menu button
right
here you will enter the
Fault time data record menu
indicated by T.1T.13. In this menu, some
selected important data valid at the time of the fault are recorded. This feature is intended to help the user
or the service person to determine the cause of fault.
The data available are:
T.1
Counted operation days
(Fault 43: Additional code)
d
T.2
Counted operation hours
(Fault 43: Counted operation days)
hh:mm:ss
(d)
T.3
Output frequency
(Fault 43: Counted operation hours)
Hz
(hh:mm:ss)
T.4 Motor current A
T.5 Motor voltage V
T.6 Motor power %
T.7 Motor torque %
T.8 DC voltage V
T.9 Unit temperature °C
T.10 Run status
T.11 Direction
T.12 Warnings
T.13 0-speed*
Table 7-5. Fault time recorded data
* Tells the user if the drive was at zero speed (< 0.01 Hz) when the fault occurred
Real time record
If real time is set to run on the frequency converter the data items T1 and T2 will appear as follows:
T.1
Counted operation days
yyyy-mm-
dd
T.2
Counted operation hours
hh:mm:ss,s
ss
- NX Variable Speed Drives 1
- Installation Manual 1
- Contents 4
- Trend NX Drives 5
- 1 TREND NX DRIVES 5
- 2.1 Connections 9
- (109 yds) 10
- Sensors 11
- Digital Inputs 11
- Plotting Channels 13
- 2.2 Sample Applications 14
- START-UP QUICK GUIDE 19
- CONTENTS 20
- VACON NXS/P USER’S MANUAL 20
- Document code: ud00701S 22
- Date: 7.12.2005 22
- 2.2.1 General 26
- 2.2.2 Technical criteria 26
- EU DIRECTIVE vacon • 11 28
- Vesa Laisi 28
- President 28
- 12 • vacon EU DIRECTIVE 29
- vacon • 13 30
- Drive modified 31
- TECHNICAL DATA vacon • 23 40
- 4.4 Technical data 40
- 24 • vacon TECHNICAL DATA 41
- 26 • vacon INSTALLATION 43
- INSTALLATION vacon • 27 44
- 28 • vacon INSTALLATION 45
- INSTALLATION vacon • 29 46
- 30 • vacon INSTALLATION 47
- 32 • vacon INSTALLATION 49
- Type plate 50
- Warning plate 50
- 34 • vacon INSTALLATION 51
- 5.2.1 FR4 to FR9 52
- 0009NX5 400V 0012NX5 400V 54
- 38 • vacon INSTALLATION 55
- INSTALLATION vacon • 39 56
- 40 • vacon INSTALLATION 57
- 6.1.1 Power connections 58
- 6.1.1.3 Control cable 59
- Min cable 61
- EMC Level modified 62
- Mounting procedure 64
- MAINS MOTOR 67
- Figure 6-7. Vacon NX, FR4 68
- Figure 6-9. Vacon NX, FR5 69
- Figure 6-11. Vacon NX, FR6 70
- Figure 6-13. Vacon NX, FR7 71
- Figure 6-18. Vacon NX, FR9 74
- B– B+/R+ R– 75
- on the control board 77
- Basic relay board 78
- 6.2.1.1 Control cables 79
- FAULTSTOP 84
- (See control keypad) 85
- 7.2.1 Button descriptions 86
- Location 87
- Description 87
- Number of items 87
- 13.95 Hz 89
- 2 Push the 90
- Min Frequency Min Frequency 91
- I/O term 92
- 7.3.3.2 Keypad reference 93
- Enter button 93
- 7.3.3.3 Keypad direction 93
- Active faults 94
- F T1 95
- 7.3.4.2 Fault codes 96
- 80 • vacon CONTROL KEYPAD 97
- CONTROL KEYPAD vacon • 81 98
- 82 • vacon CONTROL KEYPAD 99
- Real time record 100
- Fault history 11 Output phase 101
- Operation days 101
- PUSH to reset 101
- Menu button right 102
- 7.3.6 System menu (M6) 102
- System menu 102
- 86 • vacon CONTROL KEYPAD 103
- Francais 104
- Standard 105
- Multi-step 105
- All param 106
- Not in use 108
- Startup wizard Startup wizard 109
- Startup wizard 109
- ChangeEnable 110
- ChangeEnable ChangeDisable 110
- Timeout time 111
- Timeout time Timeout time 111
- Continuous 112
- Temperature 112
- HMI ACK timeout 113
- Trip counters 114
- Clr Optime cntr 114
- NXFIFF01 115
- A:NXOPTA1 116
- Expander boards 116
- C:NXOPTC1 117
- Parameters 117
- Slave address 117
- HOT SURFACE 118
- Reset button 120
- 104 • vacon FAULT TRACING 121
- and restart 121
- FAULT TRACING vacon • 105 122
- 106 • vacon FAULT TRACING 123
- Jum p e r b lo ck X 3 : 125
- CM A and CMB grounding 125
- 8 • vacon Basic Application 126
- 1= Offset, 4mA—20 mA 128
- Selection of language 131
- Selection of application: 131
- No editing! 132
- Stop Button Activated 133
- Trend Control Systems USA 136
© 2020, manymanuals.es. Todos los derechos reservados | 0.032 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales