Trend NX Variable Speed Drives Manual de usuario Pagina 122
- Pagina / 136
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
FAULT TRACING vacon • 105
24-hour support +358 (0)40 837 1150 • Email: [email protected]
9
Fault
code
Fault Possible cause Correcting measures
32 Fan cooling Cooling fan of the frequency converter
does not start, when ON command is
given
Contact the distributor near to you.
Please visit:
http://www.vacon.com/wwcontacts.html
34 CAN bus
communication
Sent message not acknowledged. Ensure that there is another device on
the bus with the same configuration.
35 Application Problem in application software Contact your distributor. If you are
application programmer check the
application program.
36 Control unit NXS Control Unit can not control NXP
Power Unit and vice versa
Change control unit
37 Device changed
(same type)
Option board or control unit changed.
Same type of board or same power rating
of drive.
Reset
Note: No fault time data record!
38 Device added
(same type)
Option board or drive added.
Drive of same power rating or same type
of board added.
Reset
Note: No fault time data record!
39 Device removed Option board removed.
Drive removed.
Reset
Note: No fault time data record!
40 Device
unknown
Unknown option board or drive. Contact the distributor near to you.
Please visit:
http://www.vacon.com/wwcontacts.html
41 IGBT temperature IGBT Inverter Bridge overtemperature
protection has detected too high a short
term overload current
Check loading.
Check motor size.
42 Brake resistor
overtemperature
Brake resistor overtemperature
protection has detected too heavy braking
Set the deceleration time longer.
Use external brake resistor.
43 Encoder fault Note the exceptional Fault data record.
See 7.3.4.3. Additional codes:
1 = Encoder 1 channel A is missing
2 = Encoder 1 channel B is missing
3 = Both encoder 1 channels are missing
4 = Encoder reversed
Check encoder channel connections.
Check the encoder board.
44 Device changed
(different type)
Option board or control unit changed.
Option board of different type or different
power rating of drive.
Reset
Note: No fault time data record!
Note: Application parameter values
restored to default.
45 Device added
(different type)
Option board or drive added.
Option board of different type or drive of
different power rating added.
Reset
Note: No fault time data record!
Note: Application parameter values
restored to default.
50 Analogue input
I
in
< 4mA (sel.
signal range 4
to 20 mA)
Current at the analogue input is < 4mA.
− control cable is broken or loose
− signal source has failed
Check the current loop circuitry.
51 External fault Digital input fault.
52 Keypad
communication
fault
The connection between the control
keypad and the frequency converter is
broken.
Check keypad connection and possible
keypad cable.
53 Fieldbus fault The data connection between the fieldbus
Master and the fieldbus board is broken
Check installation.
If installation is correct contact the
nearest Vacon distributor.
Please visit:
http://www.vacon.com/wwcontacts.html
- NX Variable Speed Drives 1
- Installation Manual 1
- Contents 4
- Trend NX Drives 5
- 1 TREND NX DRIVES 5
- 2.1 Connections 9
- (109 yds) 10
- Sensors 11
- Digital Inputs 11
- Plotting Channels 13
- 2.2 Sample Applications 14
- START-UP QUICK GUIDE 19
- CONTENTS 20
- VACON NXS/P USER’S MANUAL 20
- Document code: ud00701S 22
- Date: 7.12.2005 22
- 2.2.1 General 26
- 2.2.2 Technical criteria 26
- EU DIRECTIVE vacon • 11 28
- Vesa Laisi 28
- President 28
- 12 • vacon EU DIRECTIVE 29
- vacon • 13 30
- Drive modified 31
- TECHNICAL DATA vacon • 23 40
- 4.4 Technical data 40
- 24 • vacon TECHNICAL DATA 41
- 26 • vacon INSTALLATION 43
- INSTALLATION vacon • 27 44
- 28 • vacon INSTALLATION 45
- INSTALLATION vacon • 29 46
- 30 • vacon INSTALLATION 47
- 32 • vacon INSTALLATION 49
- Type plate 50
- Warning plate 50
- 34 • vacon INSTALLATION 51
- 5.2.1 FR4 to FR9 52
- 0009NX5 400V 0012NX5 400V 54
- 38 • vacon INSTALLATION 55
- INSTALLATION vacon • 39 56
- 40 • vacon INSTALLATION 57
- 6.1.1 Power connections 58
- 6.1.1.3 Control cable 59
- Min cable 61
- EMC Level modified 62
- Mounting procedure 64
- MAINS MOTOR 67
- Figure 6-7. Vacon NX, FR4 68
- Figure 6-9. Vacon NX, FR5 69
- Figure 6-11. Vacon NX, FR6 70
- Figure 6-13. Vacon NX, FR7 71
- Figure 6-18. Vacon NX, FR9 74
- B– B+/R+ R– 75
- on the control board 77
- Basic relay board 78
- 6.2.1.1 Control cables 79
- FAULTSTOP 84
- (See control keypad) 85
- 7.2.1 Button descriptions 86
- Location 87
- Description 87
- Number of items 87
- 13.95 Hz 89
- 2 Push the 90
- Min Frequency Min Frequency 91
- I/O term 92
- 7.3.3.2 Keypad reference 93
- Enter button 93
- 7.3.3.3 Keypad direction 93
- Active faults 94
- F T1 95
- 7.3.4.2 Fault codes 96
- 80 • vacon CONTROL KEYPAD 97
- CONTROL KEYPAD vacon • 81 98
- 82 • vacon CONTROL KEYPAD 99
- Real time record 100
- Fault history 11 Output phase 101
- Operation days 101
- PUSH to reset 101
- Menu button right 102
- 7.3.6 System menu (M6) 102
- System menu 102
- 86 • vacon CONTROL KEYPAD 103
- Francais 104
- Standard 105
- Multi-step 105
- All param 106
- Not in use 108
- Startup wizard Startup wizard 109
- Startup wizard 109
- ChangeEnable 110
- ChangeEnable ChangeDisable 110
- Timeout time 111
- Timeout time Timeout time 111
- Continuous 112
- Temperature 112
- HMI ACK timeout 113
- Trip counters 114
- Clr Optime cntr 114
- NXFIFF01 115
- A:NXOPTA1 116
- Expander boards 116
- C:NXOPTC1 117
- Parameters 117
- Slave address 117
- HOT SURFACE 118
- Reset button 120
- 104 • vacon FAULT TRACING 121
- and restart 121
- FAULT TRACING vacon • 105 122
- 106 • vacon FAULT TRACING 123
- Jum p e r b lo ck X 3 : 125
- CM A and CMB grounding 125
- 8 • vacon Basic Application 126
- 1= Offset, 4mA—20 mA 128
- Selection of language 131
- Selection of application: 131
- No editing! 132
- Stop Button Activated 133
- Trend Control Systems USA 136
© 2020, manymanuals.es. Todos los derechos reservados | 0.081 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales